The answer, unfortunately is not definitive. Usually, yes. But, because of no strict standardization enforcement it may not work. I’d say better to order DDR3 if that is what originally came with your motherboard.
More info below.
Slot Ddr3l Dipasang Ddr3 Ddr4
From: www.tomshardware.com/ans…
DDR3L modules are backwards compatible with DDR3 by design.
DDR3L adalah DDR3 low-voltage. Artinya dia bisa dipasang di slot DDR3 standar (1,5 volt) atau bisa di slot DDR3L (1,3 volt). Modul memori DDR3 yang dipasang di slot DDR3L bakalan tidak stabil karena dia minta 1,5 volt tapi hanya diberi 1,3 volt. Sebaliknya modul DDR3L bisa beroperasi baik 1,5 maupun 1,3 volt. No one here seems to know it. I have a vaio ST series which rewuires a ddr3l and a lenovo x230 that runs on ddr3. I used the ddr3 on the lenovo to the vaio and the vaio detected it and worked well. I guess the diffrence is with the power. Putting a ddr3 will make your battery to discharge faster compared to getting a ddr3l. Solved: My laptop has a DDR3L slot into which I have insertead a DDR3 memory stick. I can't get the right type in the near future. This setup works - 5960098. DDR3 memory on the other hand is actually 1.5Vs. Now the primary problem is that Intel has officially listed support for DDR3L standard, not DDR3, which actually has a voltage of 1.35V.
Manufacturers use the same integrated circuits for DDR3 and DDR3L. The highest quality ICs are tested for operating at 1.35 volts and are branded as DDR3L if they run properly. Other than that, there’s no difference between them.
Hello,
Slot Ddr3l Dipasang Ddr3 Ram
yes it is correct, that they should use the same Chips. So from a functionallity point of view it is really just the same compatibility issue as with DDR3 from one vendor to another vendor (or even just for one die shrink to the next die shrink).
![Slot Ddr3l Dipasang Ddr3 Slot Ddr3l Dipasang Ddr3](/uploads/1/3/4/3/134379542/819978998.jpg)
JEDEC defines that the DIMM needs to be backward compatible. So if a JEDEC compliant DIMM is operating at 1.5V should be tested and verified from the vendor. But not too many DIMM vendors really state that the DIMM is JEDEC compliant.
E. g. I have seen DIMMs with devices not supporting specific CL that they would need to support to be JEDEC compliant ..
E. g. I have seen DIMMs with devices not supporting specific CL that they would need to support to be JEDEC compliant ..
And in this case thre is no need that the DIMM really is backward compatible (even if it is just a question of Speed, or reliability over time).
Even standard DIMMs are theoretically interchangable, there are many compatibility issues between motherboard, controller and DIMM out there .. and DDR3L will not make it better ..
Even standard DIMMs are theoretically interchangable, there are many compatibility issues between motherboard, controller and DIMM out there .. and DDR3L will not make it better ..
Guess thats the usual difference between theory and praxis ..
and so I prefer to look at the DIMM spec and at least verify that the 1.5V is a supported voltage on a DDR3L DIMM if I intend to use it in a DDR3 System…
and so I prefer to look at the DIMM spec and at least verify that the 1.5V is a supported voltage on a DDR3L DIMM if I intend to use it in a DDR3 System…
Hermann